System #5 Pipe Markers™ Polyester Stick-On Labels

  • High temperature, chemical and weather resistant makes this marker the most durable you can buy anywhere.
  • UV Printed legend is laminated between two layers of polyester, creating an extremely DURABLE product.
  • Self adhesive markers you peel and stick
  • Markers' adhesive has been formulated with an extra heavy coating to ensure adhesion to a variety of different pipe and insulation surfaces.
  • Markers should only be applied to clean and dry surfaces.
  • Markers comply with ANSI & ASME standards if used in conjunction with arrows.
  • Durability: 5 to 8 years outdoors Mid Continental US
  • Service Temp: -40° to 248°F (-40° to 120°C)
  • Minimum Application Temp: 50°F (10°C).
  • Surface Prep: Clean & Dry
  • Spec Compliance: ANSI / ASME A13.1
EZmarkersimgArrow

Marker Size, Letter Height and Maximum Characters per Marker

The following chart shows the recommended pipe marker letter height and marker size based on the outside pipe diameter of the pipe to be identified. For pipes smaller than 3/4" and for valve identification, the use of a permanent legible tag is recommended.

Pipe O.D. Text Size Marker Style Maximum Characters
1-1/2" - 2" 3/4" 1SM 18
2-1/2" - 7-7/8" 1-1/4" 1 22
8" - 10" 2-1/2" 1LG 22
Over 10" 3-1/2" 1XLG 22
Ilust. of Pipe Marker for Pipe O.D. of 1.25 to 2.375 inches

Style 1SM

For pipes with O.D. of 1-1/2" to 2-3/8" (38 to 60mm)
Legend Size: 3/4" (19mm) high
Marker Size: 8 x 1-1/8" (203 x 29 mm)
EZ Arrow Size: 4 x 1-1/8" (102 x 29mm)
Arrow Banding Tape Size: 1" (25.4mm)

Ilust. of Pipe Marker for Pipe O.D. of 2.5 to 6 inches

Style 1

For pipes with O.D. of 2-1/2" to 7-7/8" (64 to 150mm)
Legend Size: 1-1/4" (32mm) high
Marker Size: 14 x 2-1/4" (356 x 57mm)
EZ Arrow Size: 6 x 2-1/4" (152 x 57mm)
Arrow Banding Tape Size: 2" (51mm)

Ilust. of Pipe Marker for Pipe O.D. of 8 to 10 inches

Style 1LG

For pipes with O.D. of 8" to 10" (200 to 250mm)
Legend Size: 2-1/2" (64mm) high
Marker Size: 24 x 4" (610 x 102mm)
EZ Arrow Size: 7 x 4" (178 x 102mm)
Arrow Banding Tape Size: 4" (102mm)

Ilust. of Pipe Marker for Pipe O.D. over 10 inches

Style 1XLG

For pipes with O.D. over 10" (250mm)
Legend Size: 3-1/2" (89mm) high
Marker Size: 32 x 4" (813 x 102mm)
EZ Arrow Size: 7 x 4" (178 x 102mm)
Arrow Banding Tape Size: 4" (102mm)

Colors:

The secondary means of identification is the color code of the marker. The exact colors are contained in the ANSI Z535.1 Safety Color Code.

Color is the secondary means to identification but many times the most important. The color of the marker should be used to identify the characteristic hazard of the contents of the pipe. The following chart list the classifications shown by ANSI / ASME A13.1 2015 as the suggested color combinations for the pipe markers.

ANSI / ASME A13.1 Designation of Colors

FLUID SERVICE COLOR COMBINATIONS
Fire Quenching Fluids Colors Yellow/Black
Toxic & Corrosive Fluids Colors Yellow/Black
Flammable & *Oxidizing Fluids Colors Yellow/Black
Combustible Fluids Colors Yellow/Black
Potable, Cooling, Boiler feed, & other Water Colors Yellow/Black
Compressed Air Colors Yellow/Black
Defined by the User Colors Yellow/Black
Defined by the User Colors Yellow/Black
Defined by the User Colors Yellow/Black
Defined by the User Colors Yellow/Black
* New 2015 classification, Oxidizing Fluids

Installation Recommendations:

Ilust. of Pipe Marker for Pipe O.D. of .75 to 1.25 inches
Install pipe labels close to valves or flanges
Ilust. of Pipe Marker for Pipe O.D. of 1.25 to 2.375 inches
Install pipe labels near branches and whenever a pipe changes direction.
Ilust. of Pipe Marker for Pipe O.D. of .75 to 1.25 inches
Install pipe labels before and after all wall, floor and ceiling penetrations
Ilust. of Pipe Marker for Pipe O.D. of .75 to 1.25 inches
Install pipe labels at frequent intervals on straight pipe runs.
Brimar recommends 25 ft.