SYSTEM #4 PIPE MARKERS™ (High Temp Markers)

These markers are designed to withstand harsh chemicals, abrasion, and weather all environments. The printed legend is laminated between two layers of polyester, creating an extremely DURABLE product.

UV Printed legend is laminated between two layers of polyester, creating an extremely DURABLE product.
These Markers are available in 2 ways, markers that Wrap Around pipe and markers that are laminated to Black Carrier (Strap On).
For pipe diameters 1/2" thru 7-7/8" use Wrap Markers (Styles 4A, 4B, 4E, 4F) these markers will wrap around pipe and are secured in place by an overlapping clear adhesive strip.
For pipe diameters 8" or larger use Strap On Markers (Styles 4G & 4H) these markers are laminated to a heat and chemical resistant carrier that is then strapped on to pipe with nylon ties or stainless steel strapping.
Durability: 5 to 8 years outdoors
Service Temp: -40° to 248° F
Minimum Application Temp: None
Spec Compliance: ANSI / ASME A13.1 2015

MARKER SIZE, LETTER HEIGHT & MAX. CHARACTERS PER MARKER CHART

The following chart shows the recommended pipe marker letter height and marker size based on the outside pipe diameter of the pipe to be identified. For pipes smaller than 3/4" and for valve identification, the use of a permanent legible tag is recommended.

Pipe O.D.	Text Size	Marker Style	Maximum Characters
1/2" to 1"	1/2"	4A	22
1-1/8" to 2-3/8"	3/4"	4B	18
2-1/2" to 4-3/4"	1-1/4"	4E	22
5" to 7-7/8"	1-1/4"	4F	22
8" to 10"	2-1/2"	4G	22
Over 10"	3-1/2"	4H	16

STYLE 4A (Wrap Around)

For pipes with O.D. of 1/2" to 1": Legend Size: 1/2" High; Marker Size: 8"wide

STYLE 4B (Wrap Around)

For pipes with O.D. of 1-1/8" to 2-3/8": Legend Size: 3/4" High; Marker Size: 8" wide

STYLE 4E (Wrap Around)

For pipes with O.D. of 2-1/2" to 4-3/4": Legend Size: 1-1/4" high; Marker Size: 12" wide

STYLE 4F (Wrap Around)

For pipes with O.D. of 5" to 7-7/8": Legend Size: 1-1/4" high; Marker Size: 12" wide

STYLE 4G (Wrap Around)

For pipes with O.D. of 8" to 10": Legend Size: 2-1/2" high; Marker Size: 24" wide

STYLE 4H (Strap On)

For pipes with O.D. Over 10": Legend Size: 3-1/2" High; Marker Size: 32" wide

Colors:

The secondary means of identification is the color code of the marker. The exact colors are contained in the ANSI Z535.1 Safety Color Code.

Color is the secondary means to identification but many times the most important. The color of the marker should be used to identify the characteristic hazard of the contents of the pipe. The following chart list the classifications shown by ANSI / ASME A13.1 2015 as the suggested color combinations for the pipe markers.

ANSI / ASME A13.1 Designation of Colors

FLUID SERVICE	COLOR COMBINATIONS
Fire Quenching Fluids
Toxic & Corrosive Fluids
*Flammable & Oxidizing Fluids**
Combustible Fluids
Potable, Cooling, Boiler feed, & other Water
Compressed Air
Defined by the User
Defined by the User
Defined by the User
Defined by the User
* New 2015 classification, Oxidizing Fluids

Installation Recommendations:

Install pipe labels close to valves or flanges	Install pipe labels near branches and whenever a pipe changes direction.
Install pipe labels before and after all wall, floor and ceiling penetrations	Install pipe labels at frequent intervals on straight pipe runs. Brimar recommends 25 ft.